search

ActiGraph ACTITRAINER Bedienungsanleitung Seite 22

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 94
  • Inhaltsverzeichnis
  • LESEZEICHEN
    • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 21
22 | Page
15 W. Main St. Pensacola, FL 32502 tel 850.332-7900 fax 850-332-7904
Recharging and LED Decoding
Recharging is automatic and is accomplished by connecting the device to a standard USB port. Charging time will depend
on the battery life, but typically will not exceed four hours for a fully depleted battery. Once the battery is completely
charged (max voltage of approximately 4.18V), the LED light will remain illuminated. If the battery voltage drops below
3.1 volts while in use, the Actigraphs will not have sufficient power to collect data and will warn the user through a
series of coded flashes (see Table 6 and Table 7). The battery level, reported in volts, can be viewed at any time by
starting ActiLife and plugging in the device.
Important: The ActiLife 5 software will not allow initialization if the voltage is below 3.82 volts.
ActiGraph GT3X+ Connected to PC
Red LED (Fault Indicator)
2 Flashes
Li-Ion Battery is Faulty
3 Flashes
A hardware failure occurred while recording data.
Contact customer support at
support@theactigraph.com
Green LED
1 Flash
Battery Charging
Multiple Flashes
Communicating with PC via USB
Steady On
Battery Fully Charged
ActiGraph GT3X+ Not Connected to PC
Red LED (Fault Indicator)
No Flashing
(LED Off)
Normal operating condition or battery dead
2 Flashes
Low Battery (use ActiLife Lifestyle software to check for remaining battery life). The
unit needs to be recharged.
3 Flashes
- Unexpected Battery Failure (Temporary battery power loss)
or
- Battery Level has fallen below 3.1V and the unit has entered Halt Mode
Green LED
No Flashing
(LED Off)
Actively collecting data (“Flash Mode” disabled) or battery dead
1 Flash
- Delay before start mode (the LED always flashes prior to starting data collection)
-
Actively taking data ("Flash Mode" enabled – not recommended)
2 Flashes
N/A
3 Flashes
-
End of memory reached (Device no longer collecting data)
- Battery died while unit was in delay before start mode (no data collected on
device)
Note: The Red LED will ALWAYS flash to indicate LOW BATTERY regardless of whether "Flash Mode" is enabled or disabled. If
a “stop time” (optional) has been reached, the Green LED will stop flashing all together regardless of its previous state.
Table 6 – GT3X+ LED Reference Table
Seitenansicht 21
1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 93 94

Kommentare zu diesen Handbüchern

Keine Kommentare
  • Gamo Elipson WS-Spalluto Plush Athena
  • IHome Bluetooth-Musikempfänger GE Kühlschränke Hotpoint Kühl- und Gefrierschränke GE Kaffeemacher De'Longhi Friteusen
  • Philips HTS8100/59 Gateway Memory Card Reader Samsung TC191W Chevrolet 2001 Lumina LG PB62G
  • Panasonic DPMC210 Bedienungsanleitung Kodak D4000 Bedienungsanleitung Warehouse of Tiffany RL1304/5 Bedienerhandbuch Hp ProLiant DL145 Bedienungsanleitung Dell Venue 8 3840 Bedienungsanleitung